QGIS has support for approximately 2,700 known CRSs. Definitions for each CRS are stored in a SQLite database that is installed with QGIS. Normally, you do not need to manipulate the database directly. In fact, doing so may cause projection support to fail. Custom CRSs are stored in a user database. See section Custom Coordinate Reference System for information on managing your custom coordinate reference systems. The CRSs available in QGIS are based on those defined by the European Petroleum Search Group (EPSG) and the Institut Geographique National de France (IGNF) and are largely abstracted from the spatial reference tables used in GDAL. EPSG identifiers are present in the database and can be used to specify a CRS in QGIS. In order to use OTF projection, either your data must contain information about its coordinate reference system or you will need to define a global, layer or project-wide CRS. For PostGIS layers, QGIS uses the spatial reference identifier that was specified when the layer was created. For data supported by OGR, QGIS relies on the presence of a recognized means of specifying the CRS. In the case of shapefiles, this means a file containing the well-known text (WKT) specification of the CRS. This projection file has the same base name as the shapefile and a .prj extension. For example, a shapefile named alaska.shp would have a corresponding projection file named alaska.prj. Whenever you select a new CRS, the layer units will automatically be changed in the General tab of the Project Properties dialog under the Project (Gnome, OS X) or Settings (KDE, Windows) menu. QGIS starts each new project using the global default projection. The global default CRS is EPSG:4326 - WGS 84 (proj=longlat +ellps=WGS84 +datum=WGS84 +no_defs), and it comes predefined in QGIS. This default can be changed via the [Select...] button in the first section, which is used to define the default coordinate reference system for new projects, as shown in figure_projection_1. This choice will be saved for use in subsequent QGIS sessions. When you use layers that do not have a CRS, you need to define how QGIS responds to these layers. This can be done globally or project-wide in the CRS tab under Settings ‣ Options. If you want to define the coordinate reference system for a certain layer without CRS information, you can also do that in the General tab of the raster and vector properties dialog (see General Menu for rasters and General Menu for vectors). If your layer already has a CRS defined, it will be displayed as shown in Vector Layer Properties Dialog . QGIS supports OTF reprojection for both raster and vector data. However, OTF is not activated by default. To use OTF projection, you must activate the Enable on the fly CRS transformation checkbox in the CRS tab of the Project Properties dialog. If you have already loaded a layer and you want to enable OTF projection, the best practice is to open the CRS tab of the Project Properties dialog, select a CRS, and activate the Enable ‘on the fly’ CRS transformation checkbox. The CRS status icon will no longer be greyed out, and all layers will be OTF projected to the CRS shown next to the icon. The CRS tab of the Project Properties dialog contains five important components, as shown in Figure_projection_2 and described below: If you open the Project Properties dialog from the Project menu, you must click on the CRS tab to view the CRS settings. This manual describes the use of the proj.4 and related command line utilities. The cartographic parameters used with proj.4 are described in the user manual and are the same as those used by QGIS. The Custom Coordinate Reference System Definition dialog requires only two parameters to define a user CRS: To create a new CRS, click the Add new CRS button and enter a descriptive name and the CRS parameters. Note that the Parameters must begin with a +proj= block, to represent the new coordinate reference system. You can test your CRS parameters to see if they give sane results. To do this, enter known WGS 84 latitude and longitude values in North and East fields, respectively. Click on [Calculate], and compare the results with the known values in your coordinate reference system. QGIS asks which transformation to use by opening a dialogue box displaying PROJ.4 text describing the source and destination transforms. Further information may be found by hovering over a transform. User defaults can be saved by selecting Remember selection. Source.


Яндекс.Метрика Рейтинг@Mail.ru Free Web Counter
page counter
Last Modified: April 22, 2016 @ 2:05 am